The Pololu basic relay carrier modules make it easy to control a single-pole, double-throw (SPDT) switch from low-voltage, low-current control signals. The modules are available with 5 V and 12 V power relays, and they are available pre-soldered or as partial kits that allow greater application flexibility:
The carrier board is also available without the relay or connectors for those preferring to use their own relays that have the common “sugar cube” pinout and footprint.
The carrier board routes the three relay control pins to 0.1″-spaced pins compatible with standard solderless breadboads and female servo cable connectors. The assembled version of this board has a 0.1″ straight male header soldered to these pins while the partial kit version includes 8×1 straight and right angle 0.1″ male header strips that can optionally be broken into 3×1 pieces and soldered in. The relay switch pins are routed to a set of large pads intended for use with a 3-pin 5mm-pitch terminal block and a set of smaller pads with a 0.2″ pitch, making them compatible with 0.1″ perfboards. The assembled version of this board has a terminal block soldered to these pins while the partial kit version includes a 3-pin terminal block that can be optionally soldered in.
|
|
Advantages over similar products
- Compact layout
- Two LEDs to indicate coil actuation
- Zener diode for fast current decay on relay coil
- Specification of electrical routing clearance rules on relay switch nodes
Using the relay module
 |
The switch portion of the relay is accessible on one side of the board while the control pins are routed to the other. The relay coil is powered by supplying 5 V or 12 V across the VDD and GND pins (depending on the relay), and it is activated by a digital high control signal on the EN pin. The control signal is fed directly to a BSS138 N-channel MOSFET, which in turn actuates the relay coil when the control voltage exceeds approximately 2.5 V (see BSS138 datasheet (92k pdf) for details).
The relay switch terminals COM (common), NO (normally open), and NC (normally closed) are routed on the PCB with a minimum clearance of 60 mils (1.5 mm) from other copper. The copper traces are designed to be at least 45 mil (1.1 mm) from the board edges, though manufacturing variations in the board edges can make those distances slightly lower.
In most applications, the current and voltage ratings for the module will match the ratings of the relay used. Maximum current, maximum voltage, and life expectancy are interdependent; we therefore recommend careful examination of your relay’s datasheet.
Warning: This product is not designed to or certified for any particular high-voltage safety standard. Working with voltages above 30 V can be extremely dangerous and should only be attempted by qualified individuals with appropriate equipment and protective gear.
Schematic diagram
 |
| Schematic diagram for the Pololu basic SPDT relay carrier. |
|---|
Fast Shipping & Professional Packing
We offer a broad range of shipping options owing to our long-running partnerships with UPS, FedEx and DHL. Our warehouse personnel are expertly trained and will wrap your items according to our exact and precise specifications. Your products will be subjected to an exhaustive examination before they will be properly packaged prior to being delivered. Everyday, we send to thousands of clients in multiple countries. This shows our commitment to be the largest online retailer in the world. We have distribution centers as well as warehouses in Europe as well as the USA.
Note: Orders that contain more than one product will be assigned a distinct processing time dependent on the particular item.
We will inspect each and every one of the products before they are shipped. The majority of orders are shipped within 48 hours. The delivery time will be between 3-7 working days.
Returns
The inventory is always changing, and not fully managed by us because of the involvement of many parties including the factory and our warehouse. The stock can change at any moment. Please be aware that it's possible for your order to be out of stock after you have made the order.
Our policy is valid for a period of 30 days. If 30 days have passed in the past since you purchased and we are unable to offer you a return or exchange.
To be eligible for a refund, your product must be unopened and in the same condition as you received it in. It must also be returned in its original packaging.
Related products
Component
